bend steel tubing
"
Drill Pipe Couplings Tube Machining For Drill Rods Coupling And Casing
Tube Machining For Drill Rods Coupling and Casing,Drill Pipe Coupling from TORICH Specification: OD: 3mm-150mm Wall thickness: 0.4mm-15mm Tolerance of diameter: 0.05mm; Tolerance of W.T.: 0.05mm; Concentricity: 0.05mm Straightness : 0.30mm/m Note: DN - Nominal Diameter NPS -Nominal Pipe Size Application: 1. High dimensional accuracy, the tolerance of inner and outer diameter size can be accurate to within 0.05mm, better tolerance can controled wihthin 0.025mm. Precision
DIN2391 ST52 Seamless Carbon Steel Pipe For Excavator Hydraulic Pump System
DIN2391 ST52 Seamless Carbon Steel Pipe For Excavator Hydraulic Pump System Torich is a manufacturer of precision carbon steel tube for over 20 years.have lots of experiences on manufacturing and exporting steel pipes. Standard as per DIN 2391 standard specifies the Seamless steel tubes used forMechanical and Automobile. Similar standard and material as below. JIS G3445 STKM 11A C STKM11A C C STKM 12A B C STKM14 A B C STKM 13 A B C STKM 15A B C STKM 16A C STKM 18 A C STKM 19A
Hydraulic / Pneumatic Cylinder Precision Steel Tubes Seamless 80mm Round Shape
GB/T8713-1988 Hydraulic and Puematic Cylinder Precision ID Seamless Steel Tube Precision In Diameter Samless Steel Pipe For Fluid Power Cylinder as per standard GB T8713-88 Delivery condition:Cold working/Hard Cold working/Soft Annealing.or other treatment Cylinder tubes Matarial:10 20 35 45 16Mn Which you can follow standardGB699-88 to check the Chemical component and Mechanical properties. WT ID 1.5 2.0 2.5 3.0 3.5 5.0 6.0 7.5 10.0 12.5 15.0 20.0 OD 25 28 31 35 40 32 35 36
S235JR Galvanized Square Steel Pipe Cold Formed Welded Steel Tube For Structural
S235JR Galvanized Square Steel Pipe Cold Formed Welded Steel Tube For Structural Material The S235JR galvanized square metallic pipe is made from S235JR grade carbon metal. This steel is labeled beneath the european wellknown EN 10219 and is known for its extremely good weldability and mechanical homes. The galvanization gives corrosion resistance, making it appropriate for outside and structural packages. Specification Grade: S235JR Shape: Square, but can be customized
GOST 30245 Rectangular Hollow Sections Structural Steel Pipe For Steel Building Structures
Rectangular Hollow Sections GOST 30245Steel bent closed welded square and rectangular section for building Application:for steel Building Structures. Manufacture method:Shaping the round tubular section with longitudinal weld(Automatic high frequency welding) and consequent spellerizing to square or rectangular section. The article sections shall conform to those specified in fingures 1 and 2 Remark: hHeight(width)bwidthtwall thicknessRedge radiusIInertia momentW
Welded Not Alloy ERW Steel Pipes CA55 For Lower Temperatures
ASTM A671 ERW Steel Pipes CA55 CB60 CB65 for Atmospheric and Lower Temperatures Size range :OD 400mm,WT 6mm. Production method: OD tolerance:5% of the specified outside diameter. Out of Roundness: Difference between major and minor outside diameter 1% Thickness: The minimum wall thickness at any point in the pipe shall not be more than 0.01inch 0.3mm under the specified nominal thickness. Heat treatment: 1. Without heat treatment 2. Stress released 3. Normalizing 4.
A105 2.5inch 0.104inch Heat Exchanger Tubes Cold Drawn
A105 2.5inch 0.104inch Corrugated Fin Shall and tube Heat Exchanger Tubes and Pipes material Basic introduction: Corrugated Tube Heat Exchanger has better demand than plate type heat exchanger because of their unique design and better transferring efficiency.Torich supply corrugated tubes size from 9.52mm to 50mm ,Material from carbon steel ,stainless steel ,and Ti material. Corrugated tube enhanced technology is for no-phase and condensing heat transfer. The key of this
Round Stainless Steel Heat Exchanger Tube High Efficiency Boiler Tube
Round Stainless Steel Heat Exchanger Tube High Efficiency Boiler Tube Heat exchanger tube bundles Standard :ASTM A213 ASTM A269 ASTM A270 EN10216-5 ASTM B622 ASTM B516 ASTM A789,ETC Dimension:O.D. 1/4-1-3/4(6.35-44.5mm)W.T. 0.028'-0.15'(0.71-3.81mm) Length Max.30m Type: U bend Tube /straight Tubing Characteristic: 1.Advanced Technology of Cold drawn machine. 70 meters long cold drawn machine can produce 53 meters long for each pipe.+ Advanced technology for South Korea
10*2 12*1 Small Bore Tubing For Nozzle Chemical Injection Liquid System
10*2 **1 12*1 Small Bore Tubing For Nozzle Chemical Injection Liquid System Quick detail: Standard:EN 10305-1 DIN2391 Material: E235 E355 1010 1020 10# 20# St37 St42 etc Size: 4-12mm WT:05-7mm Description: Chemical composition of EN 10305-1 Steel Grade C Si Mn P S Al Steel name Steel number max max max max max min E215 1.0212 0.10 0.05 0.70 0.025 0.025 0.025 E235 1.0308 0.17 0.35 1.20 0.025 0.025 - E355 1.0580 0.22 0.55 1.60 0.025 0.025 - Mechanical and techological
