JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 electric resistance welded (ERW) carbon steel tubes are manufactured for automotive structural components requiring controlled mechanical properties, dimensional accuracy, and reliable forming performance. These tubes are produced from hot-rolled or cold-rolled steel strip using electric resistance welding, with optional cold finishing and heat treatment according to the required delivery condition.
TORICH supplies JIS G3472 automotive steel tubing in grades including STAM290GA, STAM290GB, STAM340G, STAM390G, STAM440G, STAM470G, STAM500G, STAM440H, STAM470H, STAM500H, and STAM540H.
Under JIS G3472:2022, the specified minimum tensile strengths range from 290 MPa to 540 MPa, depending on the grade. G-series tubes are intended for general automotive structural components, while H-series grades emphasize higher yield strength for applications requiring greater resistance to permanent deformation.
The standard generally covers tubes with outside diameters from 15.9 mm to 101.6 mm. Material grade, finishing condition, dimensional tolerance class, and internal weld bead requirements should be specified according to the final component design.
1. Product Specifications
| Parameter |
Specification |
| Product Name | JIS G3472 ERW Carbon Steel Automotive Tubes |
| Material | Carbon structural steel |
| Manufacturing Standard | JIS G3472:2022 |
| Steel Grades | STAM290GA, STAM290GB, STAM340G, STAM390G, STAM440G, STAM470G, STAM500G, STAM440H, STAM470H, STAM500H, STAM540H |
| Manufacturing Process | Electric resistance welding (ERW) |
| Outside Diameter (OD) | 15.9–101.6 mm, standard general range |
| Wall Thickness (WT) | 1.0–6.0 mm, depending on available OD/WT combinations |
| Length | 1–12 m, customizable subject to manufacturing and transportation feasibility |
| Dimensional Tolerances | JIS G3472 tolerance Classes 1, 2, or 3, as specified |
| Straightness | According to the agreed drawing or purchase specification |
| Cross Section | Round |
| Surface Condition | As-welded, cold-finished, or hot-finished; protective oil available upon request |
| Heat Treatment | As-manufactured or suitably heat-treated according to the specified delivery condition |
| Weld Bead Treatment | External bead removed; internal bead as-welded, flattened, or cut to the specified class |
| Tube Ends | Plain ends; precision cutting available |
| Inspection | Chemical analysis, tensile testing, dimensional inspection, flaring testing, and optional nondestructive testing |
| Inspection Documents | According to JIS G0415 and agreed purchaser requirements |
Dimensional Tolerance Reference
JIS G3472 defines several dimensional tolerance classes depending on the manufacturing and finishing conditions.
| Tolerance Category |
Applicable Dimension |
Permissible Deviation |
| OD Class 1 | 15.9 mm ≤ D < 50 mm | ±0.25 mm |
| OD Class 1 | 50 mm ≤ D ≤ 101.6 mm | ±0.5% |
| OD Class 3 | 15.9 mm ≤ D < 25 mm | ±0.12 mm |
| OD Class 3 | 25 mm ≤ D < 50 mm | ±0.15 mm |
| OD Class 3 | 50 mm ≤ D ≤ 101.6 mm | By agreement |
| WT Class 1 | t < 3 mm | ±0.30 mm |
| WT Class 1 | t ≥ 3 mm | ±10% |
| WT Class 3 | t < 2 mm | ±0.10 mm |
| WT Class 3 | t ≥ 2 mm | ±5% |
Notes:
- Class 3 tolerances are normally associated with cold-finished tubing. Class 2 tolerances are also specified in JIS G3472 and can be selected where appropriate.
- Wall thickness tolerances do not apply to the welded portion. Length tolerances, straightness, and additional dimensional requirements should be agreed upon before manufacturing.
2. Main Features
Controlled Strength and Formability
JIS G3472 provides automotive tube grades with specified minimum tensile and yield strengths. For example, STAM290GA requires a minimum tensile strength of 290 MPa and a minimum yield strength of 175 MPa. STAM440G increases these values to 440 MPa and 305 MPa, respectively.
For applications requiring higher yield strength, STAM440H provides a minimum yield strength of 355 MPa while maintaining the same minimum tensile strength of 440 MPa.
Grade selection should consider required strength, bending severity, forming operations, and the final component's loading conditions.
Defined Flaring Performance
JIS G3472 specifies minimum flaring requirements to evaluate tube-end expansion performance. For example:
- STAM290GA: minimum flared diameter of 1.25D.
- STAM340G: minimum flared diameter of 1.20D.
- STAM440G: minimum flared diameter of 1.15D.
D represents the original tube outside diameter. The flaring test uses a 60° conical tool, and the tube must achieve the specified expansion without cracking. These requirements apply under the conditions prescribed by the standard. Tubes specifically supplied in the as-cold-finished condition have different provisions.
Dimensional Control and Weld Bead Management
JIS G3472 distinguishes between outside diameter tolerances, wall thickness tolerances, and internal weld bead requirements. For cold-finished tubing with an outside diameter of 25 mm to less than 50 mm, OD Class 3 permits a deviation of ±0.15 mm.
The internal weld bead can also be processed according to a selected bead-height class. For example, Class 4 specifies an internal bead height deviation of 0 to +0.25 mm. These requirements are particularly relevant when the tube is subsequently cut, formed, or assembled with internal components.
3. Our Advantages
Internal Weld Bead Control for Assembly Compatibility
An excessive internal weld bead can interfere with inserted components, internal tooling, or subsequent forming operations. TORICH can review internal bead treatment requirements before production, including whether the bead should remain as-welded, be flattened, or be removed by cutting.
For applications requiring a controlled internal profile, the purchase specification can define the applicable JIS G3472 bead-height class. This reduces the risk of discovering internal clearance problems during component assembly.
Dimensional Tolerances Matched to the Actual Manufacturing Process
A common procurement problem is specifying a tight outside diameter tolerance without identifying the required manufacturing and finishing condition. JIS G3472 differentiates between as-welded, hot-finished, and cold-finished tubing.
TORICH can review the relationship between the requested outside diameter, wall thickness, finishing process, and tolerance class before confirming the manufacturing specification. This helps prevent unsuitable tolerance assumptions and unnecessary secondary processing.
Documented Material Verification and Optional Nondestructive Testing
For automotive component manufacturing, consistent material identification and inspection records are important for supplier qualification and production traceability. TORICH can arrange inspection documentation identifying the material grade, dimensions, manufacturing condition, and applicable test results.
Where required, the purchase specification can include supplementary nondestructive examination under JIS G3472 Annex A:
- Z3: Ultrasonic examination according to JIS G0582.
- Z4: Eddy current examination according to JIS G0583.
These supplementary examinations must be specified at the ordering stage. They are not automatically required for every JIS G3472 tube.
4. Applicable Standards
The primary manufacturing and inspection requirements are governed by JIS G3472:2022. Other international standards may be considered when reviewing alternative tubing specifications.
| Standard System |
Standard |
Description |
| JIS | JIS G3472:2022 | Electric resistance welded carbon steel tubes for automobile |
| ASTM | ASTM A513/A513M | Electric resistance welded carbon and alloy steel mechanical tubing |
| EN | EN 10305-3:2023 | Welded cold-sized steel tubes for precision applications |
| GOST | GOST 10705-80 | Electrically welded steel tubes, technical specifications |
| GB | GB/T 13793 | Longitudinal electric resistance welded steel tubes |
Technical note: ASTM, EN, GOST, and GB standards are listed for comparison of related product categories. They are not automatically equivalent to JIS G3472. Chemical composition, mechanical properties, dimensional tolerances, and inspection requirements must be evaluated individually before any material substitution.
Additional JIS inspection references include JIS G0320 for heat analysis, JIS G0321 for product analysis, JIS Z2241 for tensile testing, and JIS G0415 for inspection documents.
5. Application: Automotive Seat-Frame Crossmember Tubes
Automotive Seat-Frame Crossmember Manufacturing
JIS G3472 ERW carbon steel tubes can be used to manufacture tubular crossmembers incorporated into automotive seat-frame assemblies. These components connect structural sections of the seat frame and may undergo cutting, bending, end forming, welding, and assembly during production.
Material selection depends on the required component geometry and the seat assembly's structural design. Lower-strength, more formable grades such as STAM290GA or STAM340G may be considered where substantial forming is required. Higher-strength grades may be evaluated when greater resistance to permanent deformation is necessary.
For this application, the following requirements should be confirmed before production:
- Outside diameter and wall thickness after forming.
- Weld seam position relative to bending and welding operations.
- Tube-end dimensions and internal bead clearance.
- Component fatigue performance and applicable automotive validation requirements.
Compliance with JIS G3472 establishes specified tube material properties but does not, by itself, establish the crashworthiness or fatigue life of the finished seat assembly.
6. Chemical Composition
The following chemical composition limits are based on JIS G3472:2022. All values are expressed as weight percentages.
| Steel Grade |
C (%) Max. |
Si (%) Max. |
Mn (%) |
P (%) Max. |
S (%) Max. |
| STAM290GA | 0.12 | 0.35 | ≤0.60 | 0.035 | 0.035 |
| STAM340G | 0.20 | 0.35 | ≤0.60 | 0.035 | 0.035 |
| STAM390G | 0.25 | 0.35 | 0.30–0.90 | 0.035 | 0.035 |
| STAM440G | 0.25 | 0.35 | 0.30–0.90 | 0.035 | 0.035 |
| STAM440H | 0.25 | 0.35 | 0.30–0.90 | 0.035 | 0.035 |
Notes:
- The values represent specified heat-analysis composition limits.
- Niobium (Nb) and/or vanadium (V) may be added up to a maximum total of 0.15% by agreement between the manufacturer and purchaser.
- Other alloying elements may be added where permitted by the standard.
- STAM440G and STAM440H share the same specified chemical composition limits but have different mechanical property requirements.
7. Mechanical Properties
The following mechanical property requirements are based on JIS G3472:2022.
| Steel Grade |
Tensile Strength Min. (MPa) |
Yield Strength Min. (MPa) |
Elongation Min. (%) |
Flaring Requirement |
| STAM290GA | 290 | 175 | 40 | 1.25D |
| STAM340G | 340 | 195 | 35 | 1.20D |
| STAM390G | 390 | 235 | 30 | 1.20D |
| STAM440G | 440 | 305 | 25 | 1.15D |
| STAM440H | 440 | 355 | 20 | 1.15D |
Product Gallery
Frequently Asked Questions
Q: Are you a trading company or a manufacturer?
A: We are a manufacturer, and we can also provide trading services.
Q: How long is your delivery time?
A: Generally speaking, it is 10–15 days if the goods are in stock, or 30–40 days if the goods are not in stock. It depends on the quantity.
Q: Do you provide samples? Are they free or extra?
A: Yes, we can offer the sample free of charge, but the cost of freight is to be paid by the buyer.
Q: What are your terms of payment?
A: For payments of USD 2,000 or less, 100% in advance. For payments of USD 2,000 or more, 30% T/T in advance with the balance before shipment. If you have any other questions, please feel free to contact us.